WTSML | LEGACY GASKETED PHE SPARE PARTS

SWEP Plate Heat Exchanger Replacement Gaskets

Explore independent aftermarket gasket options for selected legacy SWEP and SWEP/Tranter gasketed plate heat exchanger references. Our historical catalog includes G, GF, GX, HX, MF, UX and GC model families.

These replacement seals are intended for applicable demountable plate-pack designs, not sealed brazed plate heat exchangers. Correct selection requires the original model, plate profile, fixing method and service conditions.

Request SWEP Gasket Quote →
Historical SWEP compatible replacement gasket product image from WTSML
Independent non-OEM gasket components. SWEP and related model references identify installed equipment only. Compatibility is subject to the actual exchanger construction.
  • Swep Viton Gaskets
    FKM gaskets supplied only for verified gasketed SWEP configurations
    Designed for selected chemical, hydrocarbon and elevated-temperature duties
    Construction verification excludes gasket-free brazed SWEP plate packs...
    view more
  • Swep NBR Gaskets
    NBR gaskets supplied only for verified gasketed SWEP configurations
    Commonly considered for compatible oil and industrial utility duties
    Construction verification excludes gasket-free brazed SWEP plate packs
    Profile...
    view more
  • Swep EPDM Gaskets
    EPDM gaskets supplied only for verified gasketed SWEP configurations
    Suitable for selected hot-water, HVAC and compatible aqueous duties
    Construction verification excludes gasket-free brazed SWEP plate packs
    Profile...
    view more
  • Swep Compatible Gaskets
    Compatible gaskets supplied only for verified gasketed SWEP configurations
    Construction verification excludes permanently brazed SWEP plate packs
    Profile matching covers sealing grooves, ports and retaining geometry...
    view more
  • Swep Replacement Gaskets
    Replacement gaskets supplied only for verified gasketed SWEP configurations
    Construction check prevents gasket orders for sealed brazed plate units
    Profile matching covers plate grooves, ports and gasket-retention...
    view more
  • Swep Plate Heat Exchanger Gaskets
    Replacement gaskets intended only for gasketed SWEP heat exchanger configurations
    Model verification prevents ordering gaskets for sealed brazed SWEP units
    Profile matching covers plate grooves, port seals and attachment...
    view more
Legacy SWEP-compatible gasket replacement product reference
Legacy Plate-and-Frame Sealing

Replacement Gaskets for Selected SWEP Model References

The historical spare-part range includes G, GX, GF, HX, MF, UX and GC model designations. These references are used to identify potential replacement gaskets for applicable demountable plate heat exchangers.

The original plate geometry, gasket retention method and fluid requirements must be reviewed before confirming a replacement. A matching model name alone is not proof of interchangeability.

  • Non-OEM replacement gasket enquiry
  • Historical SWEP/Tranter model references
  • Plate-pack sealing and port-ring matching
  • Glued or mechanically retained gasket designs
  • Material selection based on actual operating duty
Equipment Construction Check

Gasketed Plate Heat Exchanger or Brazed Plate Heat Exchanger?

SWEP is widely associated with brazed plate heat exchanger technology. A brazed plate exchanger has permanently joined internal plates and does not use a conventional replaceable elastomer gasket between every heat-transfer plate.

Before requesting gaskets, verify whether the installed equipment has a demountable plate pack and frame. If the equipment is a brazed unit, a different service or replacement approach may be required.

  • Check whether the plate pack can be opened.
  • Identify a removable frame and tightening bolts.
  • Confirm the nameplate and equipment type.
  • Inspect the original plate and gasket if available.
  • Do not order elastomer seals for a brazed core.
Demountable gasketed plate and frame heat exchanger reference
Equipment distinction: This category concerns replacement seals for applicable gasketed equipment. A brazed plate heat exchanger normally has no user-replaceable internal plate gaskets.
Industrial elastomer gasket reference for plate heat exchanger replacement
Sealing Compound Options

NBR, HNBR, EPDM and Fluoroelastomer Selection

The original product record lists NBRB, NBRP, HNBR, EPDM, HT EPDM and Viton A, B and G references. These are historical material options rather than confirmed universal substitutes.

The appropriate rubber formulation depends on the fluid composition, operating temperature, cleaning process and sealing requirements of the installed equipment.

  • NBRB / NBRP: historical nitrile-grade references
  • HNBR: hydrogenated nitrile elastomer family
  • EPDM: candidate for compatible aqueous services
  • HT EPDM: special grade requiring documented limits
  • Viton A/B/G: historical fluoroelastomer references
Material verification: Do not apply a generic NBR or EPDM temperature rating without knowing the exact compound, working fluid and operating conditions.
Historical SWEP Model Index

SWEP G, GF, GX, HX, MF, UX and GC Gasket Dimensions

The model references below preserve the original historical measurements. HC denotes horizontal port-center distance; VC denotes vertical port-center distance. Values are expressed in millimeters.

These tables support preliminary equipment identification. They are not certified component drawings or proof that two models with similar dimensions use interchangeable gaskets.

G Series — HC / VC

SWEP Model HC (mm) VC (mm)
G52 135 592
G58 135 822
G65 231 732
G102 226 779
G108 226 1188
G153 300 1119
G157 285 1320
G158 285 1800
G234 420 1490

GF Series — HC / VC

SWEP Model HC (mm) VC (mm)
GF59 115 535
GF138 392 1100
GF257 360 1215.5
GF276 260 1520

GX Series — HC / VC

SWEP Model HC (mm) VC (mm)
GX12 135 592
GX18 135 822
GX26 226 779
GX42 226 1183
GX51 300 1143
GX64 285 1320
GX91 285 1800
GX100 420 1490
GX145 570 1720

HX Series — HC / VC

SWEP Model HC (mm) VC (mm)
HX25 226 779
HX50 300 1143
HX85 570 1140
HX180 420 2650

MF Series — HC / VC

SWEP Model HC (mm) VC (mm)
MF56 115 392
MF59 115 535
MF138 392 1100
MF257 260 1215.5
MF276 360 1520

UX Series — HC / VC

SWEP Model HC (mm) VC (mm)
UX10 186 760
UX80 630 1860

GC Series — Model Reference

SWEP Model HC (mm) VC (mm)
GC65 — —
Dimensional cross-check: The historical G108 VC value is 1188 mm, while GX42 is 1183 mm. GF257 is recorded as 360 × 1215.5 mm, while MF257 is 260 × 1215.5 mm. These differences have been preserved exactly as supplied and require checking against the original equipment or drawings. GC65 has no recorded HC/VC values.
Gasket Attachment Design

Glue-On, Clip-On and Mechanical Retention

The original product description mentions both glued and clip-on gasket styles. The correct retention method is determined by the actual plate and gasket groove, not the equipment brand alone.

A replacement must match the sealing profile and the original attachment features. Mechanical tabs, clips, locating points and adhesive requirements should be documented before a gasket is selected.

  • Identify whether the existing seal is glued.
  • Record clips, tabs and locking features.
  • Check the complete port sealing contour.
  • Verify the correct installation procedure.
  • Do not convert fastening methods without approval.
Clip-on gasket retention structure reference
Illustration: The picture demonstrates a general clip-on retention concept. It is not a model-specific SWEP installation drawing.
Replacement gasket following a plate heat exchanger sealing groove
Flow Path and Seal Geometry

Match Port Rings and Parallel or Diagonal Routing

Historical specifications refer to parallel or diagonal flow arrangements. These describe the flow layout but do not independently identify a suitable gasket profile.

The required sealing route depends on port openings, plate orientation and the actual channel configuration. Special end-plate gasket positions may require additional identification.

  • Check the original four-port arrangement where present.
  • Compare port rings and sealing bridges.
  • Verify gasket orientation and plate sequence.
  • Identify any special end-position seals.
  • Use an original plate sample or approved drawing.
WTSML | SWEP GASKET RFQ

Request Legacy SWEP Replacement Gaskets

Send the complete model, equipment nameplate, original plate and gasket photographs, the required compound, service fluids, temperature range, quantity and delivery destination. Confirm that the equipment is a demountable gasketed plate exchanger.

Submit SWEP Gasket Enquiry →
Replacement Part Identification

How to Confirm an Older SWEP Gasket Reference

Older installations may use different model nomenclature from current product ranges. Where the nameplate or technical drawing is incomplete, the original plate and gasket become important identification references.

Document both the overall gasket contour and the retaining details. Similar HC and VC dimensions do not prove that two different series use identical seals.

  • Photograph the complete exchanger nameplate.
  • Record the full model designation.
  • Provide full-plate and gasket images.
  • Measure horizontal and vertical port centers.
  • Include fluid, temperature and material requirements.
  • Specify the required gasket quantity.
Close-up of corrugated plate heat exchanger geometry
WTSML industrial facility reference
Maintenance Planning

Prepare Gasket Sets Before Plate-Pack Service

When older gasketed exchangers are opened for cleaning or inspection, replacement seals should already be identified. Incorrect parts or missing quantities can delay reassembly.

For a site operating several G, GX, GF or HX models, maintain separate records for each plate-pack type, elastomer compound and fastening system.

  • Record installed models and plate counts.
  • Identify special gasket positions.
  • Verify quantity for each plate pack.
  • Agree material and fixing specifications.
  • Confirm delivery schedules before shutdown.
Technical Purchasing Review

Three Checks Before Approving a Replacement Order

01. Equipment Type

Confirm that the installed unit is a demountable, gasketed plate heat exchanger rather than a brazed unit.

02. Component Fit

Check the original model, plate groove, port positions, gasket geometry and retention mechanism.

03. Order Conditions

Verify compound, quantity, service conditions, inspection requirements and commercial terms.

Historical technical and commercial references: The original record mentions post-curing for four hours at 160°C, ISO9001:2000 and a one-year warranty. These are not presented as universal gasket working limits, evidence of current certification or automatically applicable warranty terms. Requirements must be confirmed for each order.
SWEP Gasket FAQ

Frequently Asked Questions

1. Do all SWEP plate heat exchangers use replaceable rubber gaskets?

No. Brazed plate heat exchangers do not have the conventional replaceable interplate rubber gaskets used in demountable gasketed plate-and-frame exchangers. Verify the installed equipment construction.

2. Are G52 and GX12 replacement gaskets interchangeable?

Their historical HC/VC values are both 135 × 592 mm, but identical port-center spacing does not prove that their gasket profiles, fixing features or sealing paths are interchangeable.

3. What information is needed to identify a SWEP gasket?

Provide the complete model, equipment nameplate, original gasket and plate photographs, port dimensions, fixing method and application conditions.

4. Is EPDM suitable for every gasketed SWEP application?

No. Suitability depends on the exact compound formulation, process fluids, operating temperatures and cleaning chemistry.

5. Are these original SWEP OEM replacement gaskets?

No. This page describes independent aftermarket gasket enquiries for selected historical equipment references. The SWEP name is used for identification only.

Related WTSML Product Families

Replacement Gaskets, Plates and Complete Heat Exchangers

If the installed equipment is a gasketed exchanger, inspect the original plates and frame during gasket renewal. If it is a brazed heat exchanger, evaluate the appropriate complete-unit service or replacement requirement instead.

As one of the most professional swep gaskets manufacturers and suppliers in China, we have world-leading production equipment and strong manufacturing capabilities. We warmly welcome you to wholesale advanced swep gaskets made in China here from our factory. Customized orders are welcome.

corrosion resistant transfer gasket
Send Inquiry
Send Inquiry