WTSML | COMPATIBLE REPLACEMENT SEALS

Hisaka Plate Heat Exchanger Replacement Gaskets

Explore aftermarket sealing options for selected Hisaka UX, SX, RX, LX, EX, GX and YX plate heat exchanger models. Replacement selection begins with the exact plate profile, gasket retention method and process fluid requirements.

UX / SX / RX / LX EX / GX / YX NBR / HNBR / EPDM FKM Material Options Glue-On / Clip-On
Browse the product listings below. Detailed model references, gasket materials and replacement identification guidance follow the product collection.
  • Hisaka Viton Gaskets
    OEM-compatible FKM (Viton®) replacement gaskets manufactured by WTSML for Hisaka plate heat exchangers operating in high-pressure chemical environments.
    Designed to resist gasket extrusion and groove stress deformation under...
    view more
  • Hisaka NBR Gaskets
    OEM-compatible NBR replacement gaskets manufactured by WTSML for Hisaka plate heat exchangers operating under dynamic pressure and intermittent start-stop conditions.
    Designed to maintain sealing integrity during pressure surges...
    view more
  • Hisaka EPDM Gaskets
    OEM-compatible EPDM replacement gaskets manufactured by WTSML for Hisaka plate heat exchangers operating in hygienic and water-based applications.
    Designed to maintain stable sealing performance under uneven plate pack...
    view more
  • Hisaka Compatible Gaskets
    OEM-compatible replacement gaskets manufactured by WTSML, developed through accurate profile reconstruction for Hisaka plate heat exchangers.
    Support legacy and unidentified models using sample-based engineering, dimensional...
    view more
  • Hisaka Replacement Gaskets
    OEM-compatible replacement gaskets manufactured by WTSML for current and legacy Hisaka plate heat exchanger models.
    Help extend equipment service life without replacing the complete heat exchanger, reducing maintenance costs and...
    view more
  • Hisaka Plate Heat Exchanger Gaskets
    OEM-compatible replacement gaskets manufactured by WTSML for a wide range of Hisaka plate heat exchanger models.
    Accurate profile matching helps reduce installation errors and supports long-term maintenance of both current and...
    view more
Historical Hisaka-compatible gasket and plate geometry reference
Replacement Sealing Components

Hisaka-Compatible Gasket Supply and Model Matching

Replacement sealing components for existing Hisaka equipment must be identified using the original plate and gasket design. A brand name or broad model family alone does not prove fit.

WTSML accepts enquiries for independent aftermarket gasket options associated with UX, SX, RX, LX, EX, GX and YX series equipment. The exact seal route, port geometry, fixing method and compound must be confirmed before quotation approval.

  • Non-OEM replacement gasket category
  • Plate-and-frame heat exchanger sealing
  • Glued and mechanically retained profiles
  • Parallel or diagonal port-flow references
  • Model-specific material and geometry review
Fixing and Retention Details

Glue-On and Clip-On Gasket Installation Designs

The gasket retention system must correspond to the actual plate construction. Some seals are bonded into the groove using an approved adhesive, while other designs use mechanical retention features.

Port sealing boundaries and fixing geometry are equally important. Two gaskets made from the same rubber compound may not be interchangeable if their clip locations or groove patterns differ.

  • Check the complete Hisaka model suffix.
  • Inspect the original gasket at every port.
  • Photograph clips, tabs and groove details.
  • Confirm the applicable plate arrangement.
  • Use approved adhesive or installation procedures.
Rubber gasket positioned on a plate heat exchanger sealing groove
Elastomer replacement heat exchanger gasket profile
Elastomer Compounds

NBR, HNBR, EPDM and Fluoroelastomer Options

The historical Hisaka gasket catalog lists several compound references: NBRB, NBRP, HNBR, EPDM, HT EPDM and Viton A, Viton B and Viton G. These references require grade-specific verification.

Material selection depends on process media, continuous and transient temperatures, chemical concentration and cleaning conditions. A gasket's profile and its rubber formulation must both match the intended service.

  • NBRB / NBRP: historical nitrile-grade references
  • HNBR: hydrogenated nitrile elastomer family
  • EPDM: option for compatible aqueous media
  • HT EPDM: grade requiring confirmed temperature limits
  • Viton A / B / G: fluoroelastomer grade references
Compound verification: The material family alone does not determine operating temperature or chemical compatibility. The actual rubber formulation and equipment conditions must be checked.
Legacy Hisaka Model Index

Hisaka Replacement Gasket Model and Dimension Reference

The following 40 model names and available dimensions come from the historical product information supplied for this range. Measurements are intended to assist preliminary identification, not replace original manufacturer drawings.

W Historical overall plate width
H Historical overall plate height
HC Horizontal port center distance
VC Vertical port center distance
All recorded dimensions are in millimeters. The UX01, UX10 and UX10A references use W/H. Other models use HC/VC. Missing historical values are shown as a dash.

UX Series — Overall W / H

Hisaka Model W (mm) H (mm)
UX01 300 850
UX10 390 1080
UX10A 390 1080

UX Series — HC / VC

Hisaka Model HC (mm) VC (mm)
UX20 550 1540
UX20A 550 2135
UX30 610 1819
UX30A 610 1819
UX40 760 2135
UX40A 760 2135
UX80 631 1860
UX90 1300 2829
UX100 1570 3780
UX130 1570 4300

SX Series — HC / VC

Hisaka Model HC (mm) VC (mm)
SX41A 805 2165
SX41 805 2165
SX43 805 2165
SX43A 805 2165
SX70A 1090 2692
SX90 1290 3270
SX90M 1290 3270

RX Series — HC / VC

Hisaka Model HC (mm) VC (mm)
RX11A — —
RX13A 450 1080
RX30A 650 1850
RX70 985 2490

LX Series — HC / VC

Hisaka Model HC (mm) VC (mm)
LX00A 350 787
LX10A 460 1066
LX10 460 1066
LX20 580 1593
LX20A 580 1593
LX30A 650 1675
LX40 790 2075
LX40A 790 2075
LX50A 810 1995

EX Series — HC / VC

Hisaka Model HC (mm) VC (mm)
EX11 760 2100
EX11A 760 2100
EX15 550 1445
EX15A 550 1445

GX / YX Series — HC / VC

Hisaka Model HC (mm) VC (mm)
GX40 — —
GX40L — —
YX80 — —
Engineering verification: These are historical identification values. For example, the supplied UX20A HC/VC combination requires confirmation. Do not approve replacement components based on this reference alone.
Replacement Gasket Identification

What to Check Before Ordering Hisaka Gaskets

Two seals can look similar in a catalog photograph but follow different port paths or use different attachment features. The existing gasket is therefore an important reference when preparing a request.

A complete enquiry should connect the original equipment identification with the material, shape and operating requirements of the replacement component.

  • Full Hisaka model and suffix
  • Equipment nameplate photograph
  • Front and back views of the original plate
  • Gasket profile, clips and port-ring details
  • Operating medium and temperatures
  • Required quantity and shipping destination
Replacement heat exchanger gasket reference for part identification
WTSML | HISAKA GASKET ENQUIRY

Request Hisaka-Compatible Replacement Gaskets

Send your original equipment model, gasket photographs, material requirements and planned replacement quantity. WTSML can review the identification information before preparing a quotation enquiry.

Submit Gasket RFQ →
WTSML industrial factory VR reference
Maintenance Spare Parts

Plan Replacement Seals Before a Scheduled Shutdown

A planned gasket renewal requires accurate part identification and a realistic delivery schedule. Incorrect material or missing gasket sets may delay the equipment's return to service.

Prepare the installed exchanger list and confirm the quantity required for each plate pack before placing an order.

  • Record every equipment model separately.
  • Identify different gasket profiles and compounds.
  • Confirm quantities for the planned maintenance scope.
  • Check packaging and delivery requirements.
  • Agree any reserved-stock arrangement in advance.
Gasket Performance and Reliability

Material Compatibility, Compression and Service Life

Elastomer selection should reflect actual fluid exposure rather than a material name alone. Chemical concentration, temperature cycling, cleaning procedures and compression conditions all influence the service environment.

The replacement gasket must also remain aligned within its specified plate groove. A suitable compound cannot compensate for the wrong profile or incorrect assembly.

  • Verify compound suitability for both process fluids.
  • Review chemical cleaning exposure.
  • Check the plate groove for damage.
  • Follow approved plate-pack assembly procedures.
  • Confirm order-specific quality documents and terms.
WTSML industrial facility VR photograph
Historical technical and commercial references: The original product record mentions post-curing for four hours at 160°C, ISO9001:2000 and a one-year warranty. These statements are not treated as current universal manufacturing, certification or warranty commitments. Applicable requirements must be confirmed for each order.
Technical Purchasing Questions

Hisaka Gasket FAQ

1. Are these original HISAKA OEM gaskets?

No. These are independent aftermarket replacement components. HISAKA names are used for identification of existing equipment.

2. Can I select a gasket using only a Hisaka model?

The model helps identify the equipment, but the complete suffix, gasket profile, fixing design and operating conditions must also be confirmed.

3. Can a glued gasket be replaced with a clip-on gasket?

Not automatically. The plate must support the intended fixing system and the replacement geometry must be verified.

4. Does every EPDM or NBR gasket have the same temperature rating?

No. Service limits depend on the exact formulation, fluid chemistry, operating conditions and equipment requirements.

5. What information is required for a gasket quotation?

Provide the full equipment model, gasket photographs, required compound, fluid conditions, quantity and delivery destination.

Related WTSML Product Categories

Replacement Plates, Gaskets and Heat Exchangers

When renewing a plate-pack seal set, also review the condition of the plates. Damaged sealing grooves, cracks and deformation may require separate component assessment.

As one of the most professional hisaka gaskets manufacturers and suppliers in China, we have world-leading production equipment and strong manufacturing capabilities. We warmly welcome you to wholesale advanced hisaka gaskets made in China here from our factory. Customized orders are welcome.

hisaka gaskets, Hisaka Plate Heat Exchanger Gaskets, Hisaka Viton Gaskets
Send Inquiry
Send Inquiry